Gross national income

Pyramidal microwave horn antenna, with a bandwidth of 0.8 to 18 GHz. A coaxial cable feedline attaches to the connector visible at top. This type is called a ridged horn; the curving fins visible inside the mouth of the horn increase the antenna's bandwidth.

Pyramidal horn antennas for a variety of frequencies. They have flanges at the top to attach to standard waveguides.

A horn antenna or microwave horn is an antenna that consists of a flaring metal waveguide shaped like a horn to direct radio waves in a beam. Horns are widely used as antennas at UHF and microwave frequencies, above 300 MHz. They are used as feeders (called feed horns) for larger antenna structures such as parabolic antennas, as standard calibration antennas to measure the gain of other antennas, and as directive antennas for such devices as radar guns, automatic door openers, and microwave radiometers. Their advantages are moderate directivity (gain), low standing wave ratio (SWR), broad bandwidth, and simple construction and adjustment.

One of the first horn antennas was constructed in 1897 by Indian radio researcher Jagadish Chandra Bose in his pioneering experiments with microwaves. In the 1930s the first experimental research (Southworth and Barrow, 1936) and theoretical analysis (Barrow and Chu, 1939) of horns as antennas was done. The development of radar in World War 2 stimulated horn research to design feed horns for radar antennas. The corrugated horn invented by Kay in 1962 has become widely used as a feed horn for microwave antennas such as satellite dishes and radio telescopes.

An advantage of horn antennas is that since they have no resonant elements, they can operate over a wide range of frequencies, a wide bandwidth. The usable bandwidth of horn antennas is typically of the order of 10:1, and can be up to 20:1 (for example allowing it to operate from 1 GHz to 20 GHz). The input impedance is slowly varying over this wide frequency range, allowing low voltage standing wave ratio (VSWR) over the bandwidth. The gain of horn antennas ranges up to 25 dBi, with 10 - 20 dBi being typical.

Description

A horn antenna is used to transmit radio waves from a waveguide (a metal pipe used to carry radio waves) out into space, or collect radio waves into a waveguide for reception. It typically consists of a short length of rectangular or cylindrical metal tube (the waveguide), closed at one end, flaring into an open-ended conical or pyramidal shaped horn on the other end. The radio waves are usually introduced into the waveguide by a coaxial cable attached to the side, with the central conductor projecting into the waveguide to form a quarter-wave monopole antenna. The waves then radiate out the horn end in a narrow beam. However in some equipment the radio waves are conducted between the transmitter or receiver and the antenna by a waveguide, and in this case the horn is just attached to the end of the waveguide. In horns installed outdoors, such as the feed horns of satellite dishes, the open mouth of the horn is often covered by a plastic sheet which is transparent to the radio waves, to keep out moisture.

How it works

Corrugated conical horn antenna used as a feed horn on a Hughes Direcway home satellite dish. A transparent plastic sheet covers the horn mouth to keep out rain.

A horn antenna serves the same function for electromagnetic waves that an acoustical horn does for sound waves in a musical instrument such as a trumpet. It provides a gradual transition structure to match the impedance of a tube to the impedance of free space, enabling the waves from the tube to radiate efficiently into space.

If a simple open-ended waveguide is used as an antenna, without the horn, the sudden end of the conductive walls causes an abrupt impedance change at the aperture, from the wave impedance in the waveguide to the impedance of free space, (about 377 ohms). When radio waves travelling through the waveguide hit the opening, this impedance-step reflects a significant fraction of the wave energy back down the guide toward the source, so that not all of the power is radiated. This is similar to the reflection at an open-ended transmission line or a boundary between optical mediums with a low and high index of refraction, like at a glass surface. The reflected waves cause standing waves in the waveguide, increasing the SWR, wasting energy and possibly overheating the transmitter. In addition, the small aperture of the waveguide (less than one wavelength) causes significant diffraction of the waves issuing from it, resulting in a wide radiation pattern without much directivity.

To improve these poor characteristics, the ends of the waveguide are flared out to form a horn. The taper of the horn changes the impedance gradually along the horn's length. This acts like an impedance matching transformer, allowing most of the wave energy to radiate out the end of the horn into space, with minimal reflection. The taper functions similarly to a tapered transmission line, or an optical medium with a smoothly varying refractive index. In addition, the wide aperture of the horn projects the waves in a narrow beam

The horn shape that gives minimum reflected power is an exponential taper. Exponential horns are used in special applications that require minimum signal loss, such as satellite antennas and radio telescopes. However conical and pyramidal horns are most widely used, because they have straight sides and are easier to design and fabricate.

Radiation pattern

File:Bocina Cónica Corrugada.JPG

Small aperture-limited horn, used as a feed horn in a radio telescope for millimeter waves.

The waves travel down a horn as spherical wavefronts, with their origin at the apex of the horn, a point called the phase center. The pattern of electric and magnetic fields at the aperture plane at the mouth of the horn, which determines the radiation pattern, is a scaled-up reproduction of the fields in the waveguide. However, because the wavefronts are spherical, the phase increases smoothly from the edges of the aperture plane to the center, because of the difference in length of the center point and the edge points from the apex point. The difference in phase between the center point and the edges is called the phase error. This phase error, which increases with the flare angle, reduces the gain and increases the beamwidth, giving horns wider beamwidths than similar-sized plane-wave antennas such as parabolic dishes.

At the flare angle, the radiation of the beam lobe is down about -20 dB from its maximum value.

As the size of a horn in wavelengths is increased, the phase error increases, giving the horn a wider radiation pattern. Keeping the beamwidth narrow requires a longer horn (smaller flare angle) to keep the phase error constant. The increasing phase error limits the aperture size of practical horns to about 15 wavelengths; larger apertures would require impractically long horns. This limits the gain of practical horns to about 1000 (30 dBi) and the corresponding minimum beamwidth to about 5 - 10°.

Types

Horn antenna types

These are the common types of horn antenna. Horns can have different flare angles as well as different expansion curves (elliptic, hyperbolic, etc.) in the E-field and H-field directions, making possible a wide variety of different beam profiles.

Pyramidal horn (a, right) – a horn antenna with the horn in the shape of a four-sided pyramid, with a rectangular cross section. They are a common type, used with rectangular waveguides, and radiate linearly polarized radio waves.

Sectoral horn – A pyramidal horn with only one pair of sides flared and the other pair parallel. It produces a fan-shaped beam, which is narrow in the plane of the flared sides, but wide in the plane of the narrow sides. These types are often used as feed horns for wide search radar antennas.

E-plane horn (b) – A sectoral horn flared in the direction of the electric or E-field in the waveguide.

H-plane horn (c) – A sectoral horn flared in the direction of the magnetic or H-field in the waveguide.

Conical horn (d) – A horn in the shape of a cone, with a circular cross section. They are used with cylindrical waveguides.

Exponential horn (e) – A horn with curved sides, in which the separation of the sides increases as an exponential function of length. Also called a scalar horn, they can have pyramidal or conical cross sections. Exponential horns have minimum internal reflections, and almost constant impedance and other characteristics over a wide frequency range. They are used in applications requiring high performance, such as feed horns for communication satellite antennas and radio telescopes.

Corrugated horn – A horn with parallel slots or grooves, small compared with a wavelength, covering the inside surface of the horn, transverse to the axis. Corrugated horns have wider bandwidth and smaller sidelobes and cross-polarization, and are widely used as feed horns for satellite dishes and radio telescopes.

Ridged horn – A pyramidal horn with ridges or fins attached to the inside of the horn, extending down the center of the sides. The fins lower the cutoff frequency, increasing the antenna's bandwidth.

Septum horn – A horn which is divided into several subhorns by metal partitions (septums) inside, attached to opposite walls.

Aperture-limited horn – a long narrow horn, long enough so the phase error is a negligible fraction of a wavelength, so it essentially radiates a plane wave. It has an aperture efficiency of 1.0 so it gives the maximum gain and minimum beamwidth for a given aperture size. The gain is not affected by the length but only limited by diffraction at the aperture. Used as feed horns in radio telescopes and other high-resolution antennas.

Optimum horn

Corrugated horn antenna with a bandwidth of 3.7 to 6 GHz designed to attach to SMA waveguide feedline. This was used as a feedhorn for a parabolic antenna on a British military base.

For a given frequency and horn length, there is some flare angle that gives minimum reflection and maximum gain. The internal reflections in straight-sided horns come from the two locations along the wave path where the impedance changes abruptly; the mouth or aperture of the horn, and the throat where the sides begin to flare out. The amount of reflection at these two sites varies with the flare angle of the horn (the angle the sides make with the axis). In narrow horns with small flare angles most of the reflection occurs at the mouth of the horn. The gain of the antenna is low because the small mouth approximates an open-ended waveguide. As the angle is increased, the reflection at the mouth decreases rapidly and the antenna's gain increases. In contrast, in wide horns with flare angles approaching 90° most of the reflection is at the throat. The horn's gain is again low because the throat approximates an open-ended waveguide. As the angle is decreased, the amount of reflection at this site drops, and the horn's gain again increases.

This discussion shows that there is some flare angle between 0° and 90° which gives maximum gain and minimum reflection. This is called the optimum horn. Most practical horn antennas are designed as optimum horns. In a pyramidal horn, the dimensions that give an optimum horn are:

$a_E=\sqrt{2\lambda L_E}{a}_H=\sqrt{3\lambda L_H}$

For a conical horn, the dimensions that give an optimum horn are:

$d=\sqrt{3\lambda L}$

where

a_E is the width of the aperture in the E-field direction

a_H is the width of the aperture in the H-field direction

L_E is the slant length of the side in the E-field direction

L_H is the slant length of the side in the H-field direction.

d is the diameter of the cylindrical horn aperture

L is the slant length of the cone from the apex.

λ is the wavelength

An optimum horn does not give maximum gain for a given aperture size; this is achieved by a very long horn (an aperture limited horn). It gives the maximum gain for a given horn length. Tables showing dimensions for optimum horns for various frequencies are given in microwave handbooks.

Large pyramidal horn used in 1951 to detect the 21 cm (1.43 GHz) radiation from hydrogen gas in the Milky Way galaxy.

Gain

Horns have very little loss, so the directivity of a horn is roughly equal to its gain. The gain G of a pyramidal horn antenna (the ratio of the radiated power intensity along its beam axis to the intensity of an isotropic antenna with the same input power) is:

$G=\frac{4\pi A}{{\lambda }^2}{e}_A$

For conical horns, the gain is:

$G={\left(\frac{\pi d}{\lambda }\right)}^2{e}_A$

where

A is the area of the aperture,

d is the aperture diameter of a conical horn

λ is the wavelength,

e_A is a dimensionless parameter between 0 and 1 called the aperture efficiency,

The aperture efficiency ranges from 0.4 to 0.8 in practical horn antennas. For optimum pyramidal horns, e_A = 0.511., while for optimum conical horns e_A = 0.522. So an approximate figure of 0.5 is often used. The aperture efficiency increases with the length of the horn, and for aperture-limited horns is approximately unity.

Horn-reflector antenna

A type of antenna that combines a horn with a parabolic reflector is the Hogg or horn-reflector antenna, invented by Alfred C. Beck and Harald T. Friis in 1941 and further developed by David C. Hogg at Bell labs in 1961, and is therefore typically known as the Hogg horn, or colloquially the "sugar scoop" due to its characteristic shape. It consists of a horn antenna with a reflector mounted in the mouth of the horn at a 45 degree angle so the radiated beam is at right angles to the horn axis. The reflector is a segment of a parabolic reflector, and the focus of the reflector is at the apex of the horn, so the device is equivalent to a parabolic antenna fed off-axis. The advantage of this design over a standard parabolic antenna is that the horn shields the antenna from radiation coming from angles outside the main beam axis, so its radiation pattern has very small sidelobes. Also, the aperture isn't partially obstructed by the feed and its supports, as with ordinary front-fed parabolic dishes, allowing it to achieve aperture efficiencies of 70% as opposed to 55-60% for front-fed dishes. The disadvantage is that it is far larger and heavier for a given aperture area than a parabolic dish, and must be mounted on a cumbersome turntable to be fully steerable. This design was used for a few radio telescopes and communication satellite ground antennas during the 1960s. Its largest use, however, was as fixed antennas for microwave relay links in the AT&T Long Lines microwave network. Since the 1970s this design has been superseded by shrouded parabolic dish antennas, which can achieve equally good sidelobe performance with a lighter more compact construction. Probably the most photographed and well-known example is the 15 meter (50 foot) long Holmdel Horn Antenna at Bell Labs in Holmdel, New Jersey, with which Arno Penzias and Robert Wilson discovered cosmic microwave background radiation in 1965, for which they won the 1978 Nobel Prize in Physics.

People are nonetheless rushing to buy properties in Singapore. A new residential condominium mission in Bedok had a long queue three days before its official launch and bought more than 350 units on the very first day. Nonetheless, there is a ‘development' that had emerged in 2011 that the majority have possibly overlooked.

In August, more than a hundred individuals across 16 states reportedly had been sickened with salmonella after consuming mangos In September, the Meals and Drug Administration detained mango imports from a Mexican packing house after the fruits had been linked to the sickenings Save Cash On Your Online Purchasing Make saving money when purchasing on-line a breeze with Bodge's favourite app, Invisible Hands. This helpful program does the price-checking analysis for you, and will warn you when a unique site has a better value - or let you realize that you have found the most effective deal. Watch Posted by Edison Foo September 29, 2013 HEARTH SALE!!! From only $9xx,000! We hope this listing will help launch your search for new properties in Singapore. It's unlawful to purchase ice cream after 6 pm, in Newark.

for a borrower with one or more excellent residential property loans3; and No SSD will be payable by the seller if the property is bought more than three years after it was bought. Non-extension of the Jan 2009 Funds assistance measures for the property market when the measures expire. Permitting up to 2 years of property tax deferral for land accepted for improvement. Lively secondary marketplace for easy exit of property investments. Curiosity on mortgage fee is tax deductible when the property is rented out. We've progressive property tax rates for residential properties- the higher the value of the residential property, the upper the tax charge. Why do I've to pay property tax on my house when I'm an onwer-occupier and not deriving rental earnings? Palacio Cluster Landed

After obtaining a Sale License (topic to authorities circumstances meant to guard individuals shopping for property in Singapore), he might www.rmmonline.com proceed to sell units in his growth. Funding in the property market of Singapore is likely one of the few investment choices the place utilizing the bank's cash could not be any easier. The power of expats, to make a down payment, leverage the capital and consequently improve total return on investment, is excessive in Singapore. PRs who own a HDB flat must sell their flat inside six months of buying a non-public residential property in Singapore. EVERLASTING residents (PRs) now face unprecedented limits on their skill to purchase property in Singapore. New Condo in 2013 March Foreigners are eligible for Singapore greenback mortgage loan. housing grant

Skilled property brokers in Singapore will assist the client and defend their interests throughout the acquisition, and will help safe the provide at the best possible price. The agents may even be sure that all paperwork are in order and that the vendor is the rightful proprietor of the property. Most of the property brokers share their databases with each other. Tuesday's measures come after the Monetary Authority of Singapore in June tightened rules on property loans, and closed loopholes that allowed some householders to circumvent loan restrictions and avoid paying levies when buying extra property. Contact us for a FREE housing loan analysis and to study concerning the newest mortgage to worth on Singapore housing loans. J Gateway Condominium (Bought Out) Oct, 2013

6. Completion of automotive park, roads and drains serving the housing project 5% 7. Notice of Vacant Possession (Upon obtaining Temporary Occupation Permit) The estimates given by SingaporeHousingLoan.SG's calculator are not quotations and are usually not binding in any way on SingaporeHousingLoan.sg or the consumer. The method of calculation does not exactly mirror that of which is being used by the individual monetary establishment and the data provided should be used as a information only. SingaporeHousingLoan.SG's calculator does not pre-qualify you for any housing loan from any monetary institution. Undercover Report Finds Unlawful Rat Meat Sold In London Market Unpasteurized Tempeh Linked To Salmonella Outbreak That Sickens 60 Hottest EC Launch in Sengkang!

BuyRentSingaporeProperty.com is dedicated in providing the newest residential launches, Developer's sales, new launches, resale, HIGH tasks and rental of properties in Singapore. Then there are new launch property condos in the mid-tier range. These are sometimes in the vicinity of the city fringe, in areas corresponding to Newton and Novena Tanjong Rhu. These new launch projects are popular due to their proximity to town heart, the place the enterprise and entertainment centers and all the amenities they provide, but they're usually cheaper than the City core region tasks. Why submit cheques to register for new property launches in Singapore? Riversails Apartment @ Higher Serangoon LakeVille @ Jurong Lakeside Condo by MCL Ferra Condo @ Leonie Hill

See also

• Holmdel Horn Antenna

External links

• Horn Antennas Antenna-Theory.com
• Template:Cite web on Albert LaFrance [long-lines.net] website
• U. S. patent no. 2416675 Horn antenna system, filed November 26, 1941, Alfred C. Beck, Harold T. Friis on Google Patents

References

43 year old Petroleum Engineer Harry from Deep River, usually spends time with hobbies and interests like renting movies, property developers in singapore new condominium and vehicle racing. Constantly enjoys going to destinations like Camino Real de Tierra Adentro.