Newton (unit)

From formulasearchengine
Jump to navigation Jump to search

Template:Distinguish2 Template:Use British English

Template:Infobox Unit The newton (symbol: N) is the International System of Units (SI) derived unit of force. It is named after Isaac Newton in recognition of his work on classical mechanics, specifically Newton's second law of motion.


In 1946, Conférence Générale des Poids et Mesures (CGPM) resolution 2 standardized the unit of force in the MKS system of units to be the amount needed to accelerate 1 kilogram of mass at the rate of 1 metre per second squared. The 9th CGPM, held in 1948, then adopted the name "newton" for this unit in resolution 7.[1] This name honors the English physicist and mathematician Isaac Newton, who laid the foundations for most of classical mechanics. The newton thus became the standard unit of force in le Système International d'Unités (SI), or International System of Units.

Newton's second law of motion states that F = ma, where F is the force applied, m is the mass of the object receiving the force, and a is the acceleration of the object. The newton is therefore:[2]

1 N = 1 kg⋅m/s2

where the following symbols are used for the units:

N: newton
kg: kilogram
m: metre
s: second.

In dimensional analysis:


F: force
M: mass
L: length
T: time.

Template:SI unit lowercase


  • 1 N is the force of Earth's gravity on a mass of about 102 g = (Template:Frac kg).
  • On Earth's surface, a mass of 1 kg exerts a force of approximately 9.81 N [down] (or 1.0 kilogram-force; 1 kgf = 9.80665 N by definition). The approximation of 1 kgf corresponding to 10 N (1 decanewton or daN) is sometimes used as an approximation in everyday life and in engineering.
  • The force of Earth's gravity on (= the weight of) a human being with a mass of 70 kg is approximately 686 N.
  • The dot product of force and distance is mechanical work. Thus, in SI units, a force of 1 N exerted over a distance of 1 m is 1 N⋅m of work. The Work-Energy Theorem states that the work done on a body is equal to the change in energy of the body. 1 N⋅m = 1 J (joule), the SI unit of energy.
  • It is common to see forces expressed in kilonewtons or kN, where 1 kN = 1,000 N. See SI prefix.

Common use of kilonewtons in construction

Kilonewtons are often used for stating safety holding values of fasteners, anchors, and more in the building industry. They are also often used in the specifications for rock climbing equipment. The safe working loads in both tension and shear measurements can be stated in kilonewtons. Injection moulding machines, used to manufacture plastic parts, are classed by kilonewton (i.e., the amount of clamping force they apply to the mould).

On the Earth's surface, 1 kN is about 101.97162 kilogram-force of load, so multiplying the kilonewton value by 100 (i.e. using a slightly conservative and easier to calculate value) is a good approximation.[3]

Conversion factors

Units of force
Template:Navbar newton
(SI unit)
dyne kilogram-force,
pound-force poundal
1 N ≡ 1 kg·m/s2 = 105 dyn ≈ 0.10197 kp ≈ 0.22481 Template:Lbf ≈ 7.2330 pdl
1 dyn = 10−5 N ≡ 1 g·cm/s2 ≈ 1.0197 × 10−6 kp ≈ 2.2481 × 10−6 Template:Lbf ≈ 7.2330 × 10−5 pdl
1 kp = 9.80665 N = 980665 dyn gn·(1 kg) ≈ 2.2046 Template:Lbf ≈ 70.932 pdl
1 Template:Lbf ≈ 4.448222 N ≈ 444822 dyn ≈ 0.45359 kp gn·(1 lb) ≈ 32.174 pdl
1 pdl ≈ 0.138255 N ≈ 13825 dyn ≈ 0.014098 kp ≈ 0.031081 Template:Lbf ≡ 1 lb·ft/s2
The value of gn as used in the official definition of the kilogram-force is used here for all gravitational units.


See also

Notes and references

Template:SI units