Poisson's ratio

Template:Ref improve Bluestein's FFT algorithm (1968), commonly called the chirp z-transform algorithm (1969), is a fast Fourier transform (FFT) algorithm that computes the discrete Fourier transform (DFT) of arbitrary sizes (including prime sizes) by re-expressing the DFT as a convolution. (The other algorithm for FFTs of prime sizes, Rader's algorithm, also works by rewriting the DFT as a convolution.)

In fact, Bluestein's algorithm can be used to compute more general transforms than the DFT, based on the (unilateral) z-transform (Rabiner et al., 1969).

Algorithm

Recall that the DFT is defined by the formula

$X_{k}=\sum _{n=0}^{N-1}x_{n}e^{-{\frac {2\pi i}{N}}nk}\qquad k=0,\dots ,N-1.$

If we replace the product nk in the exponent by the identity nk = –(k–n)²/2 + n²/2 + k²/2, we thus obtain:

$X_{k}=e^{-{\frac {\pi i}{N}}k^{2}}\sum _{n=0}^{N-1}\left(x_{n}e^{-{\frac {\pi i}{N}}n^{2}}\right)e^{{\frac {\pi i}{N}}(k-n)^{2}}\qquad k=0,\dots ,N-1.$

This summation is precisely a convolution of the two sequences a_n and b_n defined by:

$a_{n}=x_{n}e^{-{\frac {\pi i}{N}}n^{2}}$

$b_{n}=e^{{\frac {\pi i}{N}}n^{2}},$

with the output of the convolution multiplied by N phase factors b_k^*. That is:

$X_{k}=b_{k}^{*}\sum _{n=0}^{N-1}a_{n}b_{k-n}\qquad k=0,\dots ,N-1.$

This convolution, in turn, can be performed with a pair of FFTs (plus the pre-computed FFT of b_n) via the convolution theorem. The key point is that these FFTs are not of the same length N: such a convolution can be computed exactly from FFTs only by zero-padding it to a length greater than or equal to 2N–1. In particular, one can pad to a power of two or some other highly composite size, for which the FFT can be efficiently performed by e.g. the Cooley–Tukey algorithm in O(N log N) time. Thus, Bluestein's algorithm provides an O(N log N) way to compute prime-size DFTs, albeit several times slower than the Cooley–Tukey algorithm for composite sizes.

The use of zero-padding for the convolution in Bluestein's algorithm deserves some additional comment. Suppose we zero-pad to a length M ≥ 2N–1. This means that a_n is extended to an array A_n of length M, where A_n = a_n for 0 ≤ n < N and A_n = 0 otherwise—the usual meaning of "zero-padding". However, because of the b_k–n term in the convolution, both positive and negative values of n are required for b_n (noting that b_–n = b_n). The periodic boundaries implied by the DFT of the zero-padded array mean that –n is equivalent to M–n. Thus, b_n is extended to an array B_n of length M, where B₀ = b₀, B_n = B_M–n = b_n for 0 < n < N, and B_n = 0 otherwise. A and B are then FFTed, multiplied pointwise, and inverse FFTed to obtain the convolution of a and b, according to the usual convolution theorem.

Let us also be more precise about what type of convolution is required in Bluestein's algorithm for the DFT. If the sequence b_n were periodic in n with period N, then it would be a cyclic convolution of length N, and the zero-padding would be for computational convenience only. However, this is not generally the case:

$b_{n+N}=e^{{\frac {\pi i}{N}}(n+N)^{2}}=b_{n}e^{{\frac {\pi i}{N}}(2Nn+N^{2})}=(-1)^{N}b_{n}.$

Therefore, for N even the convolution is cyclic, but in this case N is composite and one would normally use a more efficient FFT algorithm such as Cooley–Tukey. For N odd, however, then b_n is antiperiodic and we technically have a negacyclic convolution of length N. Such distinctions disappear when one zero-pads a_n to a length of at least 2N−1 as described above, however. It is perhaps easiest, therefore, to think of it as a subset of the outputs of a simple linear convolution (i.e. no conceptual "extensions" of the data, periodic or otherwise).

z-Transforms

Bluestein's algorithm can also be used to compute a more general transform based on the (unilateral) z-transform (Rabiner et al., 1969). In particular, it can compute any transform of the form:

$X_{k}=\sum _{n=0}^{N-1}x_{n}z^{nk}\qquad k=0,\dots ,M-1,$

for an arbitrary complex number z and for differing numbers N and M of inputs and outputs. Given Bluestein's algorithm, such a transform can be used, for example, to obtain a more finely spaced interpolation of some portion of the spectrum (although the frequency resolution is still limited by the total sampling time), enhance arbitrary poles in transfer-function analyses, etcetera.

The algorithm was dubbed the chirp z-transform algorithm because, for the Fourier-transform case (|z| = 1), the sequence b_n from above is a complex sinusoid of linearly increasing frequency, which is called a (linear) chirp in radar systems.

References

• Leo I. Bluestein, "A linear filtering approach to the computation of the discrete Fourier transform," Northeast Electronics Research and Engineering Meeting Record 10, 218-219 (1968).
• Lawrence R. Rabiner, Ronald W. Schafer, and Charles M. Rader, "The chirp z-transform algorithm and its application," Bell Syst. Tech. J. 48, 1249-1292 (1969). Also published in: Rabiner, Shafer, and Rader, "The chirp z-transform algorithm," IEEE Trans. Audio Electroacoustics 17 (2), 86–92 (1969).
• D. H. Bailey and P. N. Swarztrauber, "The fractional Fourier transform and applications," SIAM Review 33, 389-404 (1991). (Note that this terminology for the z-transform is nonstandard: a fractional Fourier transform conventionally refers to an entirely different, continuous transform.)
• Lawrence Rabiner, "The chirp z-transform algorithm—a lesson in serendipity," IEEE Signal Processing Magazine 21, 118-119 (March 2004). (Historical commentary.)

External links

http://www.embedded.com/showArticle.jhtml?articleID=17301593 A DSP algorithm for frequency analysis - the Chirp-Z Transform (CZT)